Tynor Ankle Support Neoprene J12 | Heat Retention Neoprene Ankle Brace
NDIS Participants
Ankle Fractures, Sprains & Post-Op Recovery
Sports and training support
Sports injury prevention
NDIS Participant Support
The Tynor Ankle Support (Neoprene) (J-12) is a wrap-around neoprene ankle brace that provides compression, warmth and controlled support to a weak or injured ankle. A semi-rigid PE splint helps arrest inversion and eversion (side-to-side roll) while still allowing freedom in plantar flexion, giving controlled, supportive immobilisation where it's needed most. Made from a soft, four-way-stretch, three-layered neoprene that retains gentle warmth, it has anti-slip silicone bands to stop it slipping, a perforated rear for breathability, and a slim profile that fits inside a shoe. Its anatomical, bilateral design fits either the left or right ankle. One universal size (18–30 cm circumference).
- Semi-rigid splint — A semi-rigid PE splint helps arrest inversion and eversion roll while allowing freedom in plantar flexion, for controlled support and immobilisation.
- Fits both ankles — An anatomical, bilaterally symmetrical design fits either the left or right ankle.
- Premium neoprene material — Soft, durable four-way-stretch neoprene retains gentle body heat for comforting warmth.
- Anti-slip silicone bands — Silicone bands along key contact points help keep the brace in place.
- Wrap-around design — Easy to put on and take off, with customised compression and a slim profile that fits inside a shoe.
- Breathable rear — Perforated at the rear for added aeration during wear.
The Tynor Ankle Support is intended to provide compression, warmth and controlled support to a weak or injured ankle, under the direction of a qualified healthcare professional.
- Chronic ankle instability or laxity (loose ligaments)
- Ankle sprains and rollovers
- Support during swelling (oedema)
- Protective support during high-impact sport and exercise
- Support for ankles prone to repetitive injury
- Post-operative and post-cast ankle support
- Supportive compression for mild ankle osteoarthritis
ⓘ Important: Fasten the straps for an intimate fit, but not so tightly that they restrict blood flow to the foot. For the correct level of support, follow the advice of a qualified healthcare professional.
Use under the guidance of a qualified healthcare professional.
- Open the wrap-around brace and position it around the ankle.
- Align the semi-rigid splint along the sides of the ankle.
- Wrap the brace for even, comfortable compression.
- Fasten the closures for an intimate fit, without restricting blood flow to the foot.
- 1 × Tynor Ankle Support (Neoprene) (J-12)
- User instruction manual
- Close any straps before washing
- Hand wash with mild detergent in water below 30°C; do not wring
- Dry flat in the shade
- Do not dry-clean, iron or bleach
- Use under the guidance of a qualified healthcare professional
- Fasten for an intimate fit but not so tightly that it restricts blood flow to the foot
- Discontinue use and seek medical advice if you experience impaired sensation, reduced blood flow, allergic rash or itching, or if pain persists or worsens
- Consult your doctor before using this device alongside another medical device
- Misuse or improper fitting may reduce effectiveness or cause adverse effects
- Follow the instructions provided on the box
- Keep out of reach of children
What is the Ankle Support used for?
It provides compression, warmth and controlled support to a weak or injured ankle — for chronic instability, sprains, swelling and protective support during sport — as directed by a healthcare professional.
Does it fit either ankle?
Yes — the anatomical, bilateral design fits either the left or right ankle.
Can I wear it inside a shoe?
Yes — it is slim and sleek, and the anti-slip silicone bands help keep it in place.
What size is it?
One universal size, fitting an ankle circumference of 18–30 cm (measured about 5 cm above the ankle joint).
Product Code: J 12
Size: Universal (ankle circumference 18–30 cm)
Fitting: Either ankle (bilateral)
Materials: Neoprene, Nylon (Polyamide), Polyethylene (PE splint), Silicone
Device Classification: Class I Medical Device
Manufacturer: Tynor Orthotics Pvt. Ltd.
Australian Supplier: Australian Healthcare Supplies